| Texto completo | |
| Autor(es): |
Manetti, Leonardo Lachi
[1]
;
Oliveira Henriques Moita, Ana Sofia
[2]
;
de Souza, Reinaldo Rodrigues
[1]
;
Cardoso, Elaine Maria
[1]
Número total de Autores: 4
|
| Afiliação do(s) autor(es): | [1] UNESP Sao Paulo State Univ, Sch Engn, Av Brasil 56, BR-15385000 Ilha Solteira, SP - Brazil
[2] Univ Lisbon, Inst Super Tecn, Dept Mech Engn, IN, Lisbon - Portugal
Número total de Afiliações: 2
|
| Tipo de documento: | Artigo Científico |
| Fonte: | INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER; v. 152, MAY 2020. |
| Citações Web of Science: | 0 |
| Resumo | |
Pool boiling is a low-cost technique for cooling electronic devices; HFE-7100 is a dielectric fluid with advantageous properties for such application but its high wettability can cause temperature overshoot in the system. Hence, the use of porous heating surfaces improves the heat transfer performance, eliminating the temperature overshoot due to their interconnected porous, which increase the wetted area and active nucleation site density. This work addressed pool boiling tests by using HFE-7100 and copper foams with three different thicknesses: 3 mm, 2 mm, and 1 mm in order to study the vapor bubble dynamics into the foam cell and find out an optimum thickness to enhance the boiling heat transfer. The results show that high thickness, 2 mm and 3 mm, has the best performance at low heat fluxes while the lowest thickness has the best performance at high heat fluxes. At heat fluxes lower than 50 kW/m(2), the higher surface wetted area increases the natural convection zone even though the latent heat also plays an important role. At higher heat fluxes, mainly after 200 kW/m(2), the vapor bubbles are trapped at the foam structure leading to an unstable boiling pattern and prevent the liquid from rewetting the surface. Therefore, the lowest foam thickness reduces the vapor trapping into the cell; additionally, the capillary-wicking ability increases and it also improves the HTC and the dryout heat flux due to the prevention of hotspots within the foam surface. (C) 2020 Elsevier Ltd. All rights reserved. (AU) | |
| Processo FAPESP: | 19/15250-9 - Desenvolvimento de um modelo semi-empírico para predição do coeficiente de transferência de calor em espumas metálicas |
| Beneficiário: | Leonardo Lachi Manetti |
| Modalidade de apoio: | Bolsas no Exterior - Estágio de Pesquisa - Doutorado |
| Processo FAPESP: | 13/15431-7 - Análise da aplicação de nanotecnologia em processos térmicos e de conversão de energia |
| Beneficiário: | Elaine Maria Cardoso |
| Modalidade de apoio: | Auxílio à Pesquisa - Jovens Pesquisadores |
| Processo FAPESP: | 17/13813-0 - Utilização de superfícies estendidas - espumas metálicas - para intensificação da transferência de calor por ebulição |
| Beneficiário: | Leonardo Lachi Manetti |
| Modalidade de apoio: | Bolsas no Brasil - Doutorado |
| Processo FAPESP: | 19/02566-8 - Caracterização experimental do desempenho térmico e hidrodinâmico de dissipadores de calor microaletados durante a ebulição convectiva |
| Beneficiário: | Elaine Maria Cardoso |
| Modalidade de apoio: | Auxílio à Pesquisa - Regular |