Fundamentals of isothermal austenite reversion in a Ti-stabilized 12Cr-6 Ni-2 Mo super martensitic stainless steel: Thermodynamics versus experimental assessments

Author(s)

Escobar, J. D. ^{[1, 2]} ; Faria, G. A. ^[3] ; Maia, E. L. ^[1] ; Oliveira, J. P. ^[4] ; Boll, T. ^{[5, 6]} ; Seils, S. ^{[5, 6]} ; Mei, P. R. ^[1] ; Ramirez, A. J. ^[3]

Affiliation

^[1] Univ Estadual Campinas, FEM, Unicamp, Coll Mech Engn, BR-13083860 Campinas, SP - Brazil

^[2] Univ Sao Paulo, Met & Mat Engn Dept, Ave Prof Mello Moraes 2463, BR-05508030 Sao Paulo, SP - Brazil

^[3] Ohio State Univ, Dept Mat Sci & Engn, Welding Engn, 1248 Arthur E Adams Dr, Columbus, OH 43221 - USA

^[4] Univ Nova Lisboa, Fac Ciencias & Tecnol, Dept Engn Mecan & Ind, UNIDEMI, Caparica - Portugal

^[5] Karlsruhe Inst Technol, Inst Appl Mat IAM WK, Engelbert Arnold Str 4, D-76131 Karlsruhe - Germany

^[6] Karlsruhe Inst Technol, KNMF, Hermann von Helmholtz Pl 1, D-76344 Eggenstein Leopoldshafen - Germany

• Document type: Journal article
• Source: ACTA MATERIALIA; v. 174, p. 246-259, AUG 1 2019.
• Web of Science Citations: 1

Abstract

This work addresses the fundamentals of inter-critical austenite reversion in a Ti-stabilized 12Cr-6Ni-2Mo (at.%) supermartensitic stainless steel, combining thermodynamic and experimental assessments. The calculation of the temperature and composition at which ferrite and austenite phases have the same free energy, i.e. T-0 and C-0(T), respectively, is discussed as a methodology to understand the austenite reversion and stabilization mechanisms. An ultra-fast heating rate of 500 degrees C s(-1) provided isothermal austenite nucleation and growth from a fully solubilized martensite, allowing direct comparison with the compositional tie-lines and the transformation paths described by the free energy calculations. Isothermal transformation temperatures below and above T-0 (625 degrees C) were used. Below T-0, massive reversion was suppressed since it would imply a free energy increase. The opposite occurred above T-0, since the critical Ni concentration for austenite reversion was lower than for the solubilized case. Transmission electron microscopy and atom probe tomography evidenced that, in all cases, lath growth occurred by local equilibrium partitioning of Ni, along with co-segregation of ferrite-stabilizing elements (Cr and Mo) at the advancing interface. The complex interaction between Cr, Ni and Mo on the energy gain upon nucleation of austenite revealed that Cr segregation can be beneficial while the adverse effect of Mo can be quickly outbalanced by Ni. The most stable reverted laths were obtained for transformation temperatures at least 15 degrees C below T-0 with average austenite/martensite Ni partitioning factors higher than 2.0. (C) 2019 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved. (AU)

• FAPESP's process: 16/13466-6 - Correlative atom probe tomography and transmission electron microscopy on the study of M/A, B/A interfaces and precipitates after in situ heat treatments for a TRIP-assisted supermartensitic stainless steel and advanced high strength steel
• Grantee: Julian David Escobar Atehortua
• Support Opportunities: Scholarships abroad - Research Internship - Doctorate
• FAPESP's process: 14/20844-1 - In situ study on kinetics of phase transformations and thermal stability of retained austenite in TRIP-assisted advanced high strength steel
• Grantee: Julian David Escobar Atehortua
• Support Opportunities: Scholarships in Brazil - Doctorate