Temporary materials used in prosthodontics: The effect of composition, fabrication mode, and aging on mechanical properties

Author(s):Show less -

Bergamo, Edmara T. P. ; Campos, Tiago M. B. ; Piza, Mariana M. T. ; Gutierrez, Eliezer ; Lopes, Adolfo C. O. ; Witek, Lukasz ; Coelho, Paulo G. ; Celestrino, Marcos ; Carvalho, Laura F. de ; Benalcazar, Ernesto B. ; Bonfante, Estevam A.

• Document type: Journal article
• Source: JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS; v. 133, p. 10-pg., 2022-07-12.

Abstract

Purpose: To evaluate the effect of composition, fabrication mode, and thermal cycling on the mechanical properties of different polymeric systems used for temporary dental prostheses. Materials and methods: Standard bar-shaped specimens (25 x 2 x 2 mm) were fabricated of six polymeric systems of varying compositions and fabrication modes (n = 10/group): conventional PMMA (Alike, GC) - group CGC; conventional PMMA (Dencor, Cl ' assico) - group CD; bis-acryl (Tempsmart, GC) - group BGC; bis-acryl (Yprov, Yller) - group BY; milled PMMA (TelioCAD, Ivoclar) - group MI; 3D printed bis-acryl - (Cosmos Temp, Yller) group PY. Half of the specimens were subjected to 5000 thermal cycles (5 degrees C to 55 degrees C). Three-point bending tests were performed using a universal testing machine with a crosshead speed set to 0.5 mm/min. Flexural strength and elastic modulus were calculated from the collected data. FTIR spectra were recorded pre and post curing and after thermal cycling to evaluate material composition and degree of conversion. Energy-dispersive spectroscopy (EDS) and scanning electron microscope (SEM) were utilized to examine the composition and micromorphology of the systems, respectively. Data were analyzed using two-analysis of variance and Tukey tests (alpha = 0.05). Results: FTIR spectra indicated that BGC, BY and PY groups corresponded to urethane dimethacrylate systems (bis-acryl), while CGC, CD, and MI groups corresponded to monomethacrylate systems, polymethyl methacrylate (PMMA). Bis-acryl BGC system yeilded the highest flexural strength (80 MPa), followed by the milled PMMA MI system (71 MPa), both statistically significant different relative to other groups. Bis-acryl BY exhibited the lowest flexural strength (27 MPa). Thermocycling significantly increased the flexural strength of all polymeric systems (-10-15 MPa), except for the 3D-printed PY group. Bis-acryl BGC (1.89 GPa) and conventional PMMA CGC (1.66 GPa) groups exhibited the highest elastic modulus, followed by milled PMMA MI group (1.51 GPa) and conventional PMMA CD (1.45 GPa) systems, with significant difference detected between BGC group and MI and CD groups. The 3D printed PY (0.78 GPa) and bis-acryl BY (0.47 GPa) systems presented the lowest elastic modulus. Thermocycling did not have a significant influence on the elastic modulus. FTIR spectra indicate water sorption and release of unreacted monomers as well as increased degree of conversion (-5-12%) after thermal cycling. Conclusion: Composition and fabrication mode and thermal cycling significantly affected the mechanical properties of polymeric systems used for temporary dental prostheses. (AU)

• FAPESP's process: 20/12874-9 - Infiltration graded by glass in an experimental composite based on whiskers of alumina and zircônia: development, microstructural characterization and optical and mechanical properties
• Grantee: Tiago Moreira Bastos Campos
• Support Opportunities: Scholarships in Brazil - Post-Doctoral
• FAPESP's process: 20/16500-6 - Synthesis of an ATZ nanocomposite (80%ZrO2-20%Al2O3) and microstructural, optical and survival characterization before and after aging
• Grantee: Mariana Miranda de Toledo Piza
• Support Opportunities: Scholarships in Brazil - Master
• FAPESP's process: 21/06730-7 - Towards sustainable zirconia recycled from milling waste and boosted by glass infiltration for restorative use, and of the development of strong, graded, and aging resistant multilayered zirconia blocks
• Grantee: Estevam Augusto Bonfante
• Support Opportunities: Research Grants - Young Investigators Grants - Phase 2
• FAPESP's process: 19/08693-1 - Experimental glass-infiltrated alumina-zirconia composites: characterization of microstructure, optical and mechanical properties.
• Grantee: Edmara Tatiely Pedroso Bergamo
• Support Opportunities: Scholarships in Brazil - Post-Doctoral
• FAPESP's process: 22/07157-1 - Physical and mechanical characterization of a multilayered system using recycled zirconia
• Grantee: Ernesto Byron Benalcazar Jalkh
• Support Opportunities: Scholarships in Brazil - Post-Doctoral
• FAPESP's process: 21/08018-2 - Nanomechanical layer characterization of graded ATZ and ZTA composites
• Grantee: Edmara Tatiely Pedroso Bergamo
• Support Opportunities: Scholarships abroad - Research Internship - Post-doctor
• FAPESP's process: 19/14798-0 - Development of pre-sintered ZTA 80% Al2O3/20% ZrO2 composite blocks for milling in CAD/CAM system
• Grantee: Adolfo Coelho de Oliveira Lopes
• Support Opportunities: Scholarships in Brazil - Doctorate
• FAPESP's process: 16/18818-8 - Multi-User Equipment approved in grant 2012/19078-7: ElectroPuls E3000 Linear-Torsion All-Electric dynamic test instrument package
• Grantee: Estevam Augusto Bonfante
• Support Opportunities: Multi-user Equipment Program