| Full text | |
| Author(s): |
da Silva, Andrigo Elisiario
[1]
;
Cuesta, Jorge Luiz
[2]
;
Lopes, Jose Claudio
[1]
;
de Moraes, Douglas Lyra
[1]
;
Garcia, Mateus Vinicius
[1]
;
Fonteque Ribeiro, Fernando Sabino
[3]
;
de Mello, Hamilton Jose
[1]
;
De Angelo Sanchez, Luiz Eduardo
[1]
;
Aguiar, Paulo Roberto
[2]
;
Bianchi, Eduardo Carlos
[1]
Total Authors: 10
|
| Affiliation: | [1] Sao Paulo State Univ Julio de Mesquita Filho, Dept Mech Engn, Bauru Campus, Bauru, SP - Brazil
[2] Sao Paulo State Univ Julio de Mesquita Filho, Dept Elect Engn, Bauru Campus, Bauru, SP - Brazil
[3] Fed Inst Parana, Dept Control & Ind Proc, Jacarezinho Campus, Jacarezinho, Parana - Brazil
Total Affiliations: 3
|
| Document type: | Journal article |
| Source: | INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY; v. 117, n. 9-10 AUG 2021. |
| Web of Science Citations: | 0 |
| Abstract | |
Technological advances and the development of new products make it increasingly necessary to seek to improve production means to meet the growing demand for equipment and consumer goods. In this sense, the molds enable the large-scale production of complex workpieces and equipment, which could hardly be manufactured through conventional machining. Also, the molds' surface quality must be high to avoid deviations in the produced workpieces, being achieved through grinding. Thus, this work evaluates the performance of the VP50IM mold steel grinding process using feed rates of 0.25, 0.50, and 0.75 mm/min under the conventional lubrication method, comparing the results obtained with conventional wheels of white aluminum oxide, green silicon carbide, and white aluminum oxide and black silicon carbide grain tool. The comparison was made considering the results of surface roughness (Ra), roundness error, acoustic emission, G-ratio, diametrical wheel wear, tangential grinding force, grinding power, microhardness, microscopies, and grinding costs. The results' analysis shows an advantage of using the green silicon carbide grinding wheel, which even in the worst scenario (0.75 mm/min) presented 14.83% less wear, 10.81% less acoustic emission, and consumed 10.18% less grinding power in comparison to the black silicon carbide wheel, with even better results when compared to the white aluminum oxide. Meanwhile, grinding with green silicon carbide wheel produced 9.88% lower surface roughness and 4.80% less roundness error in the worst condition when compared to the black silicon carbide tool. The machining costs with green silicon carbide were very close to those observed in the grinding with white aluminum oxide and the black silicon carbide, corroborating the grinding advantage of the VP50IM mold steel with a green silicon carbide wheel. (AU) | |
| FAPESP's process: | 18/22661-2 - PERFORMANCE OF THE APPLICATION OF LIQUID NITROGEN IN THE CYLINDRICAL GRINDING OF THE NICKEL ALLOY INCONEL 718 |
| Grantee: | Mateus Vinicius Garcia |
| Support Opportunities: | Scholarships in Brazil - Scientific Initiation |
| FAPESP's process: | 19/24933-2 - EFFECT OF ANTI-CORROSIVE OIL-WATER APPLICATION ON ALUMINA GRINDING |
| Grantee: | Douglas Lyra de Moraes |
| Support Opportunities: | Scholarships in Brazil - Scientific Initiation |
| FAPESP's process: | 20/06038-3 - Performance of MQL technique with different dilutions in grinding of austempered nodular cast iron using CBN grinding wheel |
| Grantee: | Andrigo Elisiario da Silva |
| Support Opportunities: | Scholarships in Brazil - Scientific Initiation |